
Crumpet Creations Fursuit Care Guide
1. Cleaning the HeadInside:
Use a light spray of isopropyl alcohol and water (my favorite ratio is 75 percent water to 25 percent isopropyl, though equal parts works too) inside the head to sanitize after wearing. Let it air dry completely in a well-ventilated area—never store it damp.
Outside:
Use a damp microfiber cloth or standard wash rag with plain water to spot-clean fur. Avoid getting water into the eyes or electronics. A little won't hurt, but never soak the peepers! If a little soap is needed to lift dirt, you may do so, but make sure to only use a tiny drop. Gently brush with a slicker brush after it dries to keep the fur fluffy.
For Deep Cleaning:
A Bissel Little Green or upholstery spot cleaner is fine for deep cleans! There are many tutorials online to show you how to do this.
Tub Washing (ULTIMATE deep cleaning):
1.) Fill a tub with about 2 inches of warm water. Add about a tablespoon of laundry detergent and, if you'd like, about half a teaspoon of Oxiclean (make sure you're not using a harsh detergent or one that will risk dyeing your suit!). You may also use body wash or shampoo, just like you use on yourself.
2.) Place a balled-up paper towel in each eye to avoid getting them too wet (a little water won't hurt, but it's best not to soak them).
3.) Put the head in the water, facing up so only the back gets submerged, and use a washcloth to wipe the inside and outside of the head. Press down with the wet towel on areas to help wet the internal foam, and squeeze like a sponge until you are satisfied with the cleanliness. You may add a little drop of soap here and there to clean deeper if needed.
4.) Once the head is clean, drain the tub and elevate the head to start letting it drain. Once you get most of the soapy water out, I like to refill the tub with clean water to rinse it. Wipe down with a wet, clean towel and squeeze like a sponge until you've gotten all the soapy water out.
5.) Drain the tub and let the head drain while sitting in the tub. I use a milk crate turned upside down and place my head on that!
6.) To help the head dry faster, you can gently squeeze the foam, starting top to bottom (I do one hand inside the head and one on the outside, squeezing the foam between my hands so I don't crush the head).
7.) Once the majority of the water is out, brush the fur so it is all laying flat. I like to spray a bit of leave-in conditioner on my suit to help detangle and soften the fur, or a very light mix of conditioner and water. You can do without if you prefer!
8.) For drying, I put my head on a milk crate or tripod and point a fan inside. I use an industrial floor fan on the highest setting and it takes about 24 hours to fully dry (very important to make sure it's COMPLETELY dry before storing, as you don't want it to mold!). Brush a few times during the drying process and after to help keep fur fibers fluffy!
2. Hand Washing Paws & Tails:
Hand wash in a sink or tub with cold to lukewarm water. Use your choice of laundry detergent, or for hand washing, you can use body wash or even shampoo! Make sure you rinse thoroughly and hang or lay flat on a towel to dry.
Machine Washing:
Place hand paws, hooves, or gloves into a mesh laundry bag or pillowcase, secured closed. The tail should be washed in a separate bag from the gloves.
Settings: Always use Cold Water on a Gentle or Delicate cycle.
Detergent: Use a mild detergent. Avoid heavy use of fabric softeners, as they can ruin the texture of the faux fur.
Drying:
NEVER use a dryer. The heat will melt or crimp the synthetic fur fibers. Always hang dry or lay flat in front of a fan!
3. Brushing:
Use a slicker brush (the kind with fine, bent metal wires meant for pets) to keep the fur looking pristine. Always brush with the fur direction, not against it.Be gentle around seams and possible airbrushed areas to prevent thinning or color fading.
4. Storage:
Store in a cool, dry place away from direct sunlight, which can fade colors over time. Ensure the head is stored on a sturdy stand, a mannequin head to maintain its shape, or on a shelf. Pro-Tip: Don't leave the suit in a hot car. High temperatures can soften hot glue, warp foam structures, and cause damage to eyes!
5. Quick Repairs
Keep a small sewing kit with a standard and curved upholstery needle and heavy-duty thread (matching the primary fur color, though it doesn't have to match for a field repair) for quick seam repairs! Use a Blanket / locking stitch or a ladder stitch for most items.If you encounter a loose thread, do not pull it—carefully snip it with fabric scissors. A loose thread is most likely a tie off I use to connect pieces together. Snipping it back will do no harm!
